Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
The publisher is making a few good points regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content which follows.
Mounting a bath tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging project. If the old tub is readily obtainable, the job can move speedily; if you need to open up a wall to remove the old bathtub and also position the new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make sure you have actually certified yourself for the work and also are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a brand-new tub in your washroom if you have currently gotten a new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub until the level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply and also inspect all joints as well as new pipework for leakages and tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been used at the very least once as this will resolve it into its last position.
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing issues with wetness and possible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can break relatively early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on A Step-by-Step Guide to Installing a Bathtub? Place a remark further down. We'd be interested to know your thoughts about this piece. Hoping to see you back again in the near future. Remember to take the time to promote this content if you appreciated it. Thanks a lot for your time. Please check our website back soon.
Course Detail
Report this page